Home » Electrical Engineering » THE DESIGN AND CONSTRUCTION OF CAR CONTROLLER USING TELEMETRY SYSTEM
THE DESIGN AND CONSTRUCTION OF CAR CONTROLLER USING TELEMETRY SYSTEM
Sold By: Joe Project Store | Item Type: Project Material | Report this? | Attributes: 65 pages | 1-5 chapters | Amount: ₦5,000 | Marked useful: 5,311 times
Delivery: Within 24 hoursCHAPTER ONE
INTRODUCTION
The vehicle system control using telemetry application is all about using a radio wave to control and activate certain events such as the car horn, car head light, car ignition (starter) and car air conditioner etc.
This is achieved by using various tone frequencies by using an encoder via a radio frequency transmitter (low power) that provides the carrier frequency for these tones.
At the receiver end demultiplexing and decoding of these tone takes place via a detector/receiver stage. The output of the encoder is used to turn on a relay switch, which inturn connects power source to either the car engine, horn or lamp etc.
The application of thus project include space exploration, where lunar vehicles are controlled from earth station by using satellite as the medium of transfer of signals.
In the military warfare, unmanned air crafts, missiles and even armoured tanks are controlled these days by using the pinaple of telemetry applications. Other areas include GSM, where a subscriber has the total control of his telephone calls conversation through the BTS (Base Transmission or Transceiver Station). Its application are so vast and large that they are too numerous to mention.
BLOCK DIAGRAM FOR TRANSMITTER CONTROL UNIT
BLOCK DIAGRAM FOR RECEIVER CONTROL UNIT
Telemetry system has two units the transmitter and receiver. The link between the two unit is radio wave. The transmitter sends tones of different frequencies the receiver receives the tones.
TRANSMITTER
Transmitter is a device that process and possibly encode information, so as to make it suitable for transmission and subsequent reception. In a transmitter the information modulates the carrier. It superimposed an a light frequency since wave modulation varies from one system to another and may be high or low levels. Modulations is of three types amplitude modulation, frequency modulation and pulse modulation or combination of these.
FREQUENCY MODULATION:
Frequency modulation is a system in which the amplitude of the modulated carrier is constant while its frequency and rate of change are varied by the modulating signal. Frequency modulation is much more immune to noise than amplitude modulation noise vector is superimposed on the carrier.
This material content is developed to serve as a GUIDE for students to conduct academic research
Delivery: Within 24 hours
Advertise Here
Not what you were looking for? Perform a search
What's your project topic?
Comment on Facebook:
Related Project Materials
- 1.
AN INVESTIGATION INTO THE CONSEQUENCES OF OVER LOADING A TRANSFORMER
AN INVESTIGATION INTO THE CONSEQUENCES OF OVER LOADING A TRANSFORMER CHAPTER ONE INTRODUCTION Background of the study Transformers play a crucial r...More »
Item Type: Project Material | 54 pages | 1,942 engagements |
- 2.
THE ROLE OF ELECTRICITY TARIFF HIKES IN PROMOTING RENEWABLE ENERGY ADOPTION IN NIGERIA
CHAPTER ONE INTRODUCTION Background of the Study Renewable energy is energy derived from natural sources that are replenished at a higher rate than...More »
Item Type: Project Material | 54 pages | 1,456 engagements |
- 3.
AN ASSESMENT OF THE NATIONAL GRID FAILURES AND THE WAY FORWARD
CHAPTER ONE INTRODUCTION 1.1 Background of the study Electricity has become an essential element of contemporary life worldwide, serving various purpo...More »
Item Type: Project Material | 54 pages | 1,594 engagements |
- 4.
IMPACT OF FORMAL EDUCATION ON COMMUNITY DEVELOPMENT IN OREDO LOCAL GOVERNMENT, EDO STATE
ABSTRACT The broad objective of this study is to examine the impact of formal education on community development in Oredo Local Government, Edo State....More »
Item Type: Project Material | 54 pages | 7,116 engagements |
- 5.
CONSTRUCTION OF CRITICAL TEMPERATURE ALARM SYSTEM
ABSTRACT The term “critical point” is sometimes used to denote specifically the vapour liquid critical point of a material. The vapour liquid ...More »
Item Type: Project Material | 46 pages | 13,156 engagements |
- 6.
THE CONSTRUCTION OF LABORATORY EQUIPMENT FOR THE DETERMINATION / INVESTIGATION OF ELECTRICAL INSULAT...
ABSTRACT Insulation deterioration occurs on power system when insulators are subjected to abnormal stresses. Since insulators cannot resist indefinite...More »
Item Type: Project Material | 31 pages | 9,012 engagements |