DESIGN OF MELON DE-HUSKING AND SEPARATION MACHINE
Sold By: Joe Project Store | Item Type: Project Material | Report this? | Attributes: 65 pages | 1-5 chapters | Amount: ₦5,000 | Marked useful: 6,702 times
INSTANT PROJECT MATERIAL DOWNLOADTABLES OF CONTENT
CHAPTER ONE
1.1 Introduction
1.2 Description of the Design Melon
1.3 Principles of Operation
1.4 Advantages
1.5 Objectives
1.6 Scope
1.7 Beneficiaries
CHAPTER TWO
2.1 Review of Some Properties
2.2 Some Local Variety of Melon Used
2.3 Manual De-Husking
2.4 Singular Method of Manual De-Husking
2.5 Manual Batch Method of De-Husking
2.6 Mechanized Method of De-Husking
2.7 Advantages
2.8 Disadvantages
2.9 Melon Treatment Before De-Husking
CHAPTER THREE
3.1 Mechanics of Operation of Melon De-Husking
3.2 Circular Motion and Centrifugal Force (FC)
3.3 Rotational Torque (T)
3.4 Work Done by a Torque
3.5 Force Analysis on Shaft
3.6 Volume of Air Generated (VA)
CHAPTER FOUR
4.1 Design Calculations
4.2 Optimal De-Husking Speed
4.3 Angular Velocity of Ratio of the Impeller (W)
4.4 Centrifugal Force Developed (FC)
4.5 Torque Developed (T)
4.6 Power Developed (P)
4.7 Loads of Shaft of the Electric Motor
4.8 Friction and Particle Motion
4.9 Determination of the Bearing Reaction R1 and R2
CHAPTER FIVE
5.1 Manufacturing Processes for the Melon De-Husking
5.2 Assembly Process
5.3 First Test Run
5.4 Second Test Run with Treated Melon
5.5 Cost Analysis
5.6 Conclusion
5.7 Recommendation
References
CHAPTER ONE
1.1 INTRODUCTION
Nigeria is an agricultural nation. Melon (Citrullus Vulgaris) is widely cultivated in Nigeria, among other seedlings during the planting season yearly. Several tones of the melon seeds are gathered each harvesting period but only very low percentage of the total harvest are dried by atmospheric draught and bagged for storage. High percentage waste is encored due to lack of good processing and storage facilities.
Melon when properly processed yields a lot of by-products, which could be used as food or as raw material for small and large scale industrial manufacture melon is highly enriched with oil. It has about 45% oil content. The oil could be extracted to form a very good source of vegetable oil.
After pressing out the oil, the remaining product can be used as food for human of as an additive in agro-feed manufacture. Melon without oil can be grounded and used as thickener or binder in the chemical and pharmaceutical industries.
The outside shell of the melon seeds when properly harvested in large quantity can equally be used in preparation of agric feed. The shell has about (12-55) MJ/kg calorific value and therefore can be used as a source of energy for industrial use.
The major problems encountered in the processing of melon seeds are the removal of the yellow outside shell and the separation of the broken shells form the white seeds. Locally as at now, manual approach is used for the de-husking and separation. The consequence of this is low productivity, increase in processing time, and increase in human labour.
A mechanized method of de – husking and separation will definitely increase productivity, reduce processing time and bring down human labour input to the minimum.
These problems arising form the manual de-husking and separation of the melon white seed from the shell necessitated the idea of designing, constructing and testing a melon de-husking and separation machine for our local communities and industries.
1.2 DESCRIPTION OF THE DESIGNED MELON
DE-HUSKING AND SEPARATION MACHINE
The assembly drawing of the designed de-husking and separation is shown in appendix.
The machine consists of the following components namely.
1) Impeller
2) Inlet hopper
3) De-husking casing
4) Inlet channel
5) Casing cover
6) Chequer linings
7) Exit channel
8) Adapter
9) Blower
10) Electric Motor
11) Structural Stand
12) Blower Casing
13) Blower Impeller
14) Blower Casing Cover
15) Blower Suction Channel
16) Air exit channel
17) Blower mounting base
18) Flange bearings
19) Bolts and Nuts
20) Blower shaft
The de-husking impeller is housed by the de-husking casing. The casing is lined with cylindrical chequers. The cylindrical impeller is mounted very closely to the inside walls of the cylindrical casing leaving a minimal gap to contain the melon seeds as they flow through this gap from inlet channel to the exit channel. The casing is covered with a cover plate. The impeller is connected to the shaft of the electric motor through an adapter. The blower impeller is housed by the blower casing. The blower sucks air from outside through the suction channel and the impeller forces the air through exist channel as required. All the arrangements of the machine are carried by the structural base. Bolts and nuts are used to ensure proper mounting of components on the structural base.
1.3 PRINCIPLES OF OPERATION
The principle used by this machine to achieve the melon de-husking is attrition and density differential between the cracked shells and the white seeds is applied to achieve the required separation.
The electric motor provides the primary motion which rotates the de-husking impeller. The melons are introduced through the inlet hopper of gravity. The melons are directed to flow towards the walls of the casing to the chequers. The rotating impeller then rub the melons on the chequers in the direction of rotation of the impeller. The melon must be properly treated with water (moisture) arieated properly before de-husking.
The rubbing action peels the shells of the melons and equally move them along with the broken shells in the direction of rotation to the exit channel.
The blower shaft transmits motion from the electric motor to the blower impeller, thereby delivering certain quantity of air which is channel to meet the broken shells and white seeds coming out from the de-husking casing.
The broken shells being lighter than the white seeds are carried away by the air to a different direction while the white seeds move into a receiver where they are collected.
1.4 ADVANTAGES
i) The machine combines two processes in one ie de-
Husking and separation.
ii. The machine is portable and occupies
very little space.
iv. The machine is cheap when constructed locally,
compared to cost of importation.
v. The machine can be confidently be driven by a
single phase electric motor thereby making power
consumption rate very low.
Vi. De-husking and separation time is highly
reduced by using this machine.
vii. Labour input in de-husking and separation is also
drastically reduced.
viii. Productivity in de-husking and separation is
highly increased.
1.5 OBJECTIVE
(i) The objective of this project is to design, fabricate and test a melon de-husking and separation machine in order to increase productivity in melon processing and reduce human labour of manual de-husking and separation to the bearest minimum.
(ii) This project will improve the living standard of million of rural dweller who may engage in melon processing.
(iii) It will encourage the growth of small and medium scale industrial enterprise in the agric – processing nation wide.
(iv) This project will contribute to the overall economic development of the nation by encouraging indigenous engineers technologists and technicians in designing, fabricating and testing of processing machines.
1.6 SCOPE
This machine only handles treated melon. The designed machine is expected to de-husk and separate about 450 kg of melon in an hours work. This is result in about 3, 600kg or 3.6 tonnes in eight (8) hours work.
1.7 BENEFICIARIES
i) The major beneficiaries of this project are rural dweller who might engage themselves in melon processing.
ii) Small, and medium scale agro-industrial set up who produce products like vegetable oil and food items.
iii) Chemical and pharmaceutical industries who might be using extracts from melon as binders, thickeners for drugs etc.
iv) Agro – feed industries who might be using melon as additive in feed production.
This material content is developed to serve as a GUIDE for students to conduct academic research
DOWNLOAD THIS PROJECT MATERIAL NOW!
Advertise Here
Not what you were looking for? Perform a search
What's your project topic?
Comment on Facebook:
Related Project Materials
- 1.
INVESTIGATION OF THE EFFECT OF MOULDING SAND (NATURAL & SYNTHETIC) ON CASTING OF FLANGE USING ALUMIN...
ABSTRACT This study tend to investigate the effect of synthetic and natural moulding sand on casting of flange like component. In this study FUTA lo...More »
Item Type: Project Material | 50 pages | 14,060 engagements |
- 2.
DESIGN AND FABRICATION OF AN OFFICE FILE CABINET
ABSTRACT This project covers the design and fabrication of an office file cabinet. The cabinet is to keep and secure files and document for future rec...More »
Item Type: Project Material | 50 pages | 12,805 engagements |
- 3.
DESIGN AND FABRICATION OF MECHANCIAL LAWN MOWER
ABSTRACT Mechanical engineering department of the named institute has many non operational machines sequel to this fact mainten...More »
Item Type: Project Material | 50 pages | 11,132 engagements |
- 4.
THE DESIGN AND CONSTRUCTION OF HOT PRINTING MACHINE
ABSTRACT Parameters on which clear prints depends were comprehensively investigated. The study revealed that clear print dep...More »
Item Type: Project Material | 50 pages | 8,882 engagements |
- 5.
THE CONSTRUCTION AND FABRICATION OF METAL BOOKSHEET
ABSTRACT In our society today reading and writing has taken its roll as a way of measuring human knowledge. Knowledge could only be obtain succe...More »
Item Type: Project Material | 50 pages | 8,601 engagements |
- 6.
REPAIR OF AIR CONDITIONER IN MECHANICAL ENGINEERING DEPARTMENT
CHAPTER ONE 1.1 AIR CONDITIONER Indoor climate, once adjusted to human need only by opening of heating in winter and by open...More »
Item Type: Project Material | 50 pages | 8,721 engagements |