What's your project topic?

| Back |

Mechanical Engineering Project Topics & Research Materials | Final Year Research Project Topics With Free Chapter One

  • 1. INVESTIGATION OF THE EFFECT OF MOULDING SAND (NATURAL & SYNTHETIC) ON CASTING OF...

    » ABSTRACT This study tend to investigate the effect of synthetic and natural moulding sand on casting of flange like component.  In this study FUTA logo was selected to be cast using aluminium metal. The casting was carried out and the result was analysed according to the quality of casting. It was discovered that for large size component using aluminium, it is better to use synthetic sand and whi...Continue Reading »

    Item Type: Project Material |  50 pages |  14,160 engagements | 

  • 2. DESIGN AND FABRICATION OF AN OFFICE FILE CABINET

    » ABSTRACT This project covers the design and fabrication of an office file cabinet. The cabinet is to keep and secure files and document for future record. With the four drawers, it has a storing capacity of over a thousand files. Detail design of the cabinet, material selection were carried out. This cabinet is mainly for office use.     CHAPTER ONE 1.0      INTRODUCTION All over the world...Continue Reading »

    Item Type: Project Material |  50 pages |  12,884 engagements | 

  • 3. DESIGN AND FABRICATION OF MECHANCIAL LAWN MOWER

    » ABSTRACT             Mechanical engineering department of the named institute has many non operational machines sequel to this fact maintenance which resulted to non development and non maintenance of the institute community at large.           By this fact the project (mechanical lawn mower) was constructed and design to help in the development and maintenance of institution,...Continue Reading »

    Item Type: Project Material |  50 pages |  11,192 engagements | 

  • 4. THE DESIGN AND CONSTRUCTION OF HOT PRINTING MACHINE

    » ABSTRACT             Parameters on which clear prints depends were comprehensively investigated.  The study revealed that clear print depends on the impressed pressure, the working temperature and the silver print paper.   Also studied were the manners of dependence of these parameters on prints impressed on sheets of varied thickness.  The result of this investigations were util...Continue Reading »

    Item Type: Project Material |  50 pages |  8,937 engagements | 

  • 5. THE CONSTRUCTION AND FABRICATION OF METAL BOOKSHEET

    » ABSTRACT   In our society today reading and writing has taken its roll as a way of measuring human knowledge.  Knowledge could only be obtain successively by the use of books for research but unfortunately because of hard time, books have because very expensive. This has called for preservation of books already purchased, whether in the public library school or in the house hold so that it can ...Continue Reading »

    Item Type: Project Material |  50 pages |  8,680 engagements | 

  • 6. REPAIR OF AIR CONDITIONER IN MECHANICAL ENGINEERING DEPARTMENT

    » CHAPTER ONE   1.1            AIR CONDITIONER Indoor climate, once adjusted to human need only by opening of heating in winter and by opening windows or using fans.  In summer, is now capable of being varied to meet almost any comfort of industrial demand, anywhere on earth with precise automatic control. With the introduction of air conditioner, the indoor air can be controlled thro...Continue Reading »

    Item Type: Project Material |  50 pages |  8,784 engagements | 

  • 7. THE REPAIR OF A DAMAGED AIR CONDITIONER

    » ABSTRACT This project is basically on the repair of a damaged air conditioner. It is intended to provide a break through in the restoration of any damaged air conditioner and thereby curtail the huge expenses incurred in the replacement of the entire unit. This report covers an introduction into what an air conditioner is all about, it’s historical background and working principle. A view on...Continue Reading »

    Item Type: Project Material |  31 pages |  7,477 engagements | 

  • 8. THE REPAIR AND MAINTENANCE OF A FAULTY DEEP FREEZER

    » ABSTRACT Mechanical Engineering Department of the Institute of Management and Technology has many non – functional machines. This is caused as a result of poor maintenance culture, which in turn resulted to breakdown of the Deep Freezer under review. Quality and effectiveness of machine maintenance were observed. A minimized cost of maintenance and high Technology of repair were also adopted...Continue Reading »

    Item Type: Project Material |  18 pages |  6,743 engagements | 

  • 9. THE RECTIFICATION AND REPAIR OF A FAULTY AIR CONDITIONER

    » ABSTRACT In the mechanical Engineering department of institute of management and technology there and many machines but not all in are good shape or form. This may be due to inadequate maintenance, which is evident in the breakdown of air conditioner. In the case of machine maintenance, the quality and effusiveness of material were well noted. Also not left behind was the cost of maintenance which...Continue Reading »

    Item Type: Project Material |  35 pages |  7,174 engagements | 

  • 10. THE FABRICATION OF METAL SHELF

    » ABSTRACT   Bookshelf, a Mechanical arrangement of materials were documents are stored, it could be made with metal or wood.  But this one is fabricated with metal. The type of metal used in the fabrication is mild steel and square baluters. The undismountable bookshelf which has five partitions and four compartment under went many process namely, the drawing and the dimensioning of the bookshel...Continue Reading »

    Item Type: Project Material |  50 pages |  7,439 engagements | 

  • 11. THE FABRICATION OF A POLYTHENE BAG SEALING AND CUTTING MACHINE

    » ABSTRACT   This machine is meant for sealing and cutting of nylon bag of different sizes. This machine is operated with electrical system. This machine can cut and seal nylon of different sizes. It also comprises of materials as follows: Mechanical and Electrical section Mechanical section include the frame structure, lever and the pedal mechanism. Electrical section include the transformer, Regu...Continue Reading »

    Item Type: Project Material |  50 pages |  8,942 engagements | 

  • 12. THE FABRICATION OF A FOLDABLE CAMP BED

    » ABSTRACT   In this project, three alternative design solutions were considered for the foldable cam – bed. The authors utilize the local materials (with cost consideration) for the components. The merits and demerits of each of the alternative with respect to the considered group were also discusses and the solutions of the alternatives that best satisfied the limitations were selected for prod...Continue Reading »

    Item Type: Project Material |  50 pages |  7,492 engagements | 

  • 13. THE DESIGN AND FABRICATION OF MODERN LOCKABLE BOOKSHELF

    » ABSTRACT   The purpose of this project which is the design and fabrication of lockable metal shelf is to keep the files, text books, documents etc. in a safe place for future we by the institution and also it will render a maximum service to any office where it will be kept. The primary and second any delta used for the construction of this project were given to us by our supervisor. Engr. Mrs. M...Continue Reading »

    Item Type: Project Material |  50 pages |  6,606 engagements | 

  • 14. THE DESIGN AND FABRICATION OF A PILOT PRODUCTION PLANT FOR PAINTS (EMULSION AND ...

    » ABSTRACT             The concept of this project is to actualize a practical way of paint production using a locally design mixing machine which is design to meet a low cost and high standard paint.           The project cut across all forms of engineering, such as mechanical machine design of a simple industrial mixer, which is driven by an electrically made device, a 3 HP el...Continue Reading »

    Item Type: Project Material |  50 pages |  6,938 engagements | 

  • 15. THE DESIGN AND FABRICATION OF A METAL BOOKSHELF

    » ABSTRACT   Knowledge could only be obtained successfully by the use of book for research but unfortunately because of hard times, books have become very expensive.  This is called for presentation of books already purchased whether in the library or on the household so that it can be used by the future generation.  There could only be done by stacking books systematically on a book rack where...Continue Reading »

    Item Type: Project Material |  50 pages |  6,332 engagements | 

  • 16. THE DESIGN AND CONSTRUCTION OF BAKING OVEN

    » ABSTRACT   This project is aimed at producing an oven a purposeful baking oven with temperature regulator, which is economical and very convenient to use. The equipment was designed taking into consideration the case of its production, maintenance and services. The production design which includes planning drawing and specifications of materials was directly followed by the actual fabrication / m...Continue Reading »

    Item Type: Project Material |  50 pages |  7,981 engagements | 

  • 17. THE DESIGN AND CONSTRUCTION OF A WOODLATHE MACHINE

    » ABSTRACT             This work is an attempt to evolve a quicker and easier method of achieving cylindrical shape object from a work price. This will no double save considerable human labour and time wastage involved in traditional manual method of carving.           To achieve this preliminary  experiment was carried out to determine the optimum speed of this machine variou...Continue Reading »

    Item Type: Project Material |  50 pages |  6,684 engagements | 

  • 18. THE DESIGN AND CONSTRUCTION OF A SPIN DRYER

    » ABSTRACT   This work is aimed at designing and fabricating a spin dryer which can be used in drying spent grains after brewing. This will no doubt save considerable human labours and time wastage involved in conventional method of drying the spent grains by spreading on the ground. It also saves as a means of employments for our teaming population. This machine was designed after due consideratio...Continue Reading »

    Item Type: Project Material |  50 pages |  7,483 engagements | 

  • 19. THE DESIGN AND CONSTRUCTION OF A MODERN NAIL GASKET MACHINE

    » ABSTRACT   The design and fabrication of a reciprocating nail gasket is a new innovation in technology. The one in existence is manually operated. In which a punch that is adjacent to a die is mounted to the handle  which  is attached to the shaft. A helical spring that is incorporated to the shaft of the punch, helps the handle return to its initial position, which makes the machines tedious...Continue Reading »

    Item Type: Project Material |  50 pages |  6,625 engagements | 

  • 20. THE CONSTRUCTION OF TWO FACE GAS BURNER

    » ABSTRACT This project deals with the construction and fabrication of a two face gas burner. The gas components consists of the following major components; burner, injector opening, mixing tube, burner support, etc. The gas stove was constructed from medium carbon steel material. The choice of the selected material has to do with cost, and local availability. The distance between the cooking pot an...Continue Reading »

    Item Type: Project Material |  50 pages |  10,368 engagements | 

  • 21. THE CONSTRUCTION OF AN ELECTRICAL STOVE WITH THREE-OVEN APARTMENT

    » ABSTRACT           This project is concern about the construction of an electrical stove with three oven apartment is described in his project.  It was carried out in order to solve the problem often encounter in cooking and drying and at the same time finding an alternat6ive means to replace the use of  kerosine and gas for cooking and drying which are often not available due to scar...Continue Reading »

    Item Type: Project Material |  50 pages |  6,560 engagements | 

  • 22. THE CONSTRUCTION OF A STANDARD BANKING OVEN (MINI-OVEN) WITH DUAL POWER SOURCE (...

    » ABSTRACT             This project is designed to make the students utilize as many theoretical and practical concept as have been instructed in alstron to mechanical engineering workshop technology.          Students are expected to learn and apply concepts, principles about energy specially the conversions of  electrical energy to thermal energy, conduction and conventional ...Continue Reading »

    Item Type: Project Material |  50 pages |  6,872 engagements | 

  • 23. THE CONSTRUCTION OF A MOBILE REFRIGERATOR FRIDGE

    » ABSTRACT   This write up focuses attention on a detailed report and account on the process of construction and formulation of plan for the actual and physical realization of the construction of the project work captioned fabrication and construction of a mobile cooling system.  The report is therefore divided into chapters and each chapter discussed extensively such that an illiterate refrigera...Continue Reading »

    Item Type: Project Material |  50 pages |  7,617 engagements | 

  • 24. OPERATION AND MAINTENANCE SCHEDULE OF A STEAM TURBINE PLANT

    » ABSTRACT Thermal electrical power generation is one of the major methods used in Egbin thermal station. Due to inconsistency and failure in the power supply in Nigeria, there is a need for a proper operation and maintenance schedule strategy of the various kinds of power plants accessories so as to facilitate their efficiencies and functionality.   Egbin thermal station, which is one of the major...Continue Reading »

    Item Type: Project Material |  65 pages |  10,752 engagements | 

  • 25. DESIGN, SIMULATION, CONSTRUCTION AND PERFORMANCE EVALUATION OF A SOLAR OVEN

    »   Abstract   A solar ovenis a device that converts solar energy into useful heat in a confined space (oven chamber) which can be utilised for cooking and baking purposes.The oven consists of plane reflectors to concentrate the solar radiation on the collector.The heat gain is maximum if the collector and reflectors are continuously adjusted such that the incidence angle of the reflected and di...Continue Reading »

    Item Type: Project Material |  65 pages |  8,686 engagements | 


Searching makes things a lot easier.. Search for what you are looking for

What's your project topic?