REPAIR OF AN AIRCONDITIONER
Sold By: Joe Project Store | Item Type: Project Material | Report this? | Attributes: 37 pages | 1-5 chapters | Amount: ₦5,000 | 1 order. | Marked useful: 6,279 times
INSTANT PROJECT MATERIAL DOWNLOADPREFACE
A new machine/equipment will provide satisfactory service if kept in proper operating condition. The inevitability of less than 100% reliability of any machine/equipment after some period and maintenance.
Also in system of any complexity, certain replacement adjustments are necessary at various stages. Thus a vital consideration in the design of the system components and requirement of a system in the question of how quickly and easily a unit in that system can be adjusted or repaired.
Repair or rehabilitation simply means to restore to good condition, to be in a new form or to renovate.
The repair and rehabilitation of machine in the Mechanical engineering workshop Laboratory of this institute is of utmost importance considering the members of machine that are less or non-functional.
Its quite unlike a couple of years back when it was an easy talks to recommend newly produced machine.
The habit of replacement of damaged or faulty machine(s) with new once rather than repairing them should be discouraged.
The ownership of these machine/equipment should be a never ending source of satisfaction and pleasure and so, effort should be made to reactivate them.
Historically, repair/equipment has tended to be an emergency service performed in am ad-hoc faction and largely concerned with getting broken-down machine beck into service as soon as possible.
These shouldn’t have been so, rather repair/rehabilitation should be done thoroughly and perfectly. Unfortunately, the climate in West Africa course rapid deterioration I all metal objects; machine and tools are no exception.
TABLE OF CONTENT
CHAPTER ONE
1.0 Introduction
1.1 Air conditioner
1.2 Development of Air conditioning
1.3 The Aim and objectives of this project
1.4 Compressor, crankcase, Heater
1.5 Principle of Air conditioner
CHAPTER TWO
2.0 Component parts of Air conditioner
2.1 The Basic components
2.2 Other components
CHAPTER THREE
3.0 Maintenance
3.1 Types of maintenance
3.2 Repair of a damaged one horse power air conditioner
3.3 Maintenance Job carried out on the Air conditioner
3.4 Cause of Air conditioner Breakdown
3.5 Effect of Air conditioner Breakdown
3.6 Cares for domestic Air conditioners
CHAPTER FOUR
4.0 System failure
4.1 Primary causes of system failure
4.2 Test sequences
4.3 Instrument used in testing air conditioner
4.4 Air conditioner components, faults and Remedies
REFERNCE
CHAPTER ONE
1.1 AIR CONDITIONER
Indoor climate, once adjusted to human need only by opening of heating in winter and by opening windows or using fans. In summer, is now capable of being varied to meet almost any comfort of industrial demand, anywhere on earth with precise automatic control.
With the introduction of air conditioner, the indoor air can be controlled through the blowing and sucking surrounding. Thus because of its comfort to man, need for air conditioning, Engineers, contractors, manufacturers and Technicians rising on a daily basis.
Now, consider for a moment the consequences which would result up all air conditioning systems were to stop. Not only would the temperature and humidity condition become into levable, but industrial production would be adversely affected and activities involving computers, electronics, air craft, precision manufacturing, nuclear power, optics and synthetics, in fact most areas of modern progress would come to a hault.
Today in business, industry, schools, hospitals, hotels, theatres and homes, air conditioner is no longer luxury but an essential part of modern living.
1.2 DEVELOPMENT OF AN AIR CONDITIONING INDUSTRY
The development of air conditioning industry is an interesting story, illustrating well necessity for close working relationship among scientific, engineering, productions and its beginning with mechanical refrigeration. In the late 1900s. but it was not until 1917, when Nillis, H carrier began to meet the challenges of designing suitable experiment. During the 1930s, the production of air-conditioning began and by firm scientific, engineering and production basis out with a limited market for its products.
1.2 THE AIM AND THE OBJECTIVE OF THIS PROJECT
The aim of choosing this project, is to put in order the damaged air conditioner in proper shape and better condition for effective usage.
To give wide knowledge of an air conditioner, types of operation and uses to the project group (student participating in the project).
Also to show the need to repair than to rep0lace to or to purchase a new system.
It also serves as a reference to other students that are to do a similar project.
1.3 PRINCIPLE OF AIR CONDITIONER AREVERSED CARNOT CYCLE PRINCIPLE (REFRIGERATION CYCLE).
The air conditioner is related to the refrigeration, hence, both use the same principle of the reversed carnot cycle.
It is called the reversed carnot cycle because it operates in the opposite direction. In the carnot cycle, heat is received by the working fluid at a high temperature and rejected at a low temperature. Both processes are isothermal and also two isentropic processes. In this case, a net amount of positive work is done by the working fluid. this is the working of heat engines or heat pump or carnot cycle, positive work is done.
But cycles can be formed in which the reversed happens. In this case heat is added or received at a low temperature and rejected at a high temperature. By so doing, a net amount of negative work is done on the fluid. this for any refrigeration cycle, the process is made to remove heat from a space or substance to reduce its temperature and transferring that to another space or substance.
This material content is developed to serve as a GUIDE for students to conduct academic research
DOWNLOAD THIS PROJECT MATERIAL NOW!
Advertise Here
Not what you were looking for? Perform a search
What's your project topic?
Comment on Facebook:
Related Project Materials
- 1.
INVESTIGATION OF THE EFFECT OF MOULDING SAND (NATURAL & SYNTHETIC) ON CASTING OF FLANGE USING ALUMIN...
ABSTRACT This study tend to investigate the effect of synthetic and natural moulding sand on casting of flange like component. In this study FUTA lo...More »
Item Type: Project Material | 50 pages | 13,934 engagements |
- 2.
DESIGN AND FABRICATION OF AN OFFICE FILE CABINET
ABSTRACT This project covers the design and fabrication of an office file cabinet. The cabinet is to keep and secure files and document for future rec...More »
Item Type: Project Material | 50 pages | 12,696 engagements |
- 3.
DESIGN AND FABRICATION OF MECHANCIAL LAWN MOWER
ABSTRACT Mechanical engineering department of the named institute has many non operational machines sequel to this fact mainten...More »
Item Type: Project Material | 50 pages | 11,031 engagements |
- 4.
THE DESIGN AND CONSTRUCTION OF HOT PRINTING MACHINE
ABSTRACT Parameters on which clear prints depends were comprehensively investigated. The study revealed that clear print dep...More »
Item Type: Project Material | 50 pages | 8,804 engagements |
- 5.
THE CONSTRUCTION AND FABRICATION OF METAL BOOKSHEET
ABSTRACT In our society today reading and writing has taken its roll as a way of measuring human knowledge. Knowledge could only be obtain succe...More »
Item Type: Project Material | 50 pages | 8,510 engagements |
- 6.
REPAIR OF AIR CONDITIONER IN MECHANICAL ENGINEERING DEPARTMENT
CHAPTER ONE 1.1 AIR CONDITIONER Indoor climate, once adjusted to human need only by opening of heating in winter and by open...More »
Item Type: Project Material | 50 pages | 8,619 engagements |