iProject

DESIGN AND FABRICATION OF A PRINTING I BLOCK MACHINE

šŸ“„ Project MaterialšŸ“‹ 65 pagesšŸ“š Chapters 1–5šŸ’¾ MS-Word & PDF

Chapters 1–5 Ā |Ā  ₦5,000

Get Complete Project Material Now
ABSTRACT
Ā 
Parameters on which clear prints depends were comprehensively investigated. Ā The study revealed that clear print depends on the impressed pressure the working temperature and the gold foil print paper life expectancy.
Also studies were he manner of dependence of these parameters on prints impressed Ā on sheets of varied thickness. Ā The results of these investigation were Ā utizlied in the design and fabrication of an operational manual printing machine using gold foil Ā  sheet depositor clear prints were impressed on papers during the new machine’s operation.
Ā 
Ā 
LIST OF TABLES
TABLE 1 Ā - Experimental determination of pressure for printingĀ 
11- Effect of temperature on sharpness of print.
Ā 
111 " Description of (components) parts and materials use for them
Ā 
1v- comparison of cost and properties of materialsĀ 
Ā 
LIST OF FIGURES
Description
Figure 1 sketch of alternative A
Figure 2. Sketch of alternative B.
Figure 3 sketch of alternative C
Figure 4 isomeric view of hot plate square housingĀ 
Figure 5 isometric view of type holder
Figure 6 &7 load and free body diagram of crank are (Handle) and rod.
Ā 
LIST OF SYMBOLS
A " Area
A " Acceleration
D " Maximum shaft diameter
d- minimum Ā shaft diameterĀ 
e- efficiencyĀ 
k " Thermal conductivity
c " Heat capacity
x " The pressure transmissibility of lever system (press x Ā 1/duration )
t " Time
l " Length of shaft
m " Mass
m " Maximum bearding moment
p - Electric power
q " Quantity of heatĀ 
Ā 
Ā 
TABLE OF CONTENTS
Title page ii
Letter of transmittal iii
Release iv
Approval page v
Dedication vi
AcknowledgementĀ vii
Abstract viii
List of figures ix
Ā List of tablesĀ x
List of symbols xi
Table of contents xii
Ā 
CHAPTER ONEĀ 
1.1 introductionĀ 1
1.2 literature review and data collectionĀ 2
1.3 experimental determination of pressure for prating 3
1.4 design specificationĀ 9
Ā 
CHAPTER TWO
2.1 Design solutions 11
2.2 Alternative A press foot printer 11
2.3 Alternative Ā B; crank arm Ā (handle ) 14
2.4 Alternative Ā C; automatic (motorized) printerĀ 17
2.5 Comparison of alternative and choice 20
Ā 
CHAPTER THREE
3.1 Design selection and analysis of parts of chosen alternative 22
3.2 Theory of Ā design/ Ā design calculationĀ 24
3.3 The Ā design of the shaft (Hollow) 26
Ā 
CHAPTER FOUR
4.1 construction of prototype 28
4.2 generalĀ 28
4.3 material selectionĀ 29
4.4 sequence of construction and assembly 40
Ā 
CHAPTER FIVE
5.1 Testing of prototype (test " run) 40
5.2 Evaluation of machine efficiency 40
5.3 Operator’s manual 41
5.4 Costing Ā (cost analysis) 42
5.5 Problems Encounter 45
5.6 Conclusion 45
5.7 Recommendation 46
REFERENCES

This Project is for You If:

Yes, This Is My Situation — Send Me the Complete Material

Here's everything you get with the complete project package:

āœ”Chapters 1–5 (Word & PDF)
āœ”Abstract & Table of Contents
āœ”References, Citation & Bibliography
āœ”Fully Editable Microsoft Word Format
āœ”Original, Plagiarism-Free Content
āœ”Delivery Within 24 Hours
Complete package —₦10,000₦5,000
Price may return to ₦10,000 at any time.

See Our Conversations With Students on WhatsApp

Students sharing their experience after using our service

Urgent delivery confirmed
Urgent delivery confirmed
Payment received and project delivered
Payment received and project delivered
Quality work and a repeat order
Quality work and a repeat order
Returning customer appreciation
Returning customer appreciation
Customer appreciation
Customer appreciation
I’ve Seen Enough — Get Me This Project Material

What Other Students Are Saying

ā€œThe process was actually fine and I got my project quickly. The only thing I didn't really like was that I would have preferred they sent it via WhatsApp instead of email, because email took a bit of checking on my side. But once I got it, everything was already complete and I just edited small parts before submitting.ā€
Zina
Kenpoly
ā€œMy supervisor rejected my Chapter 1 and 2 and I was honestly lost. I got a material here and it already had everything arranged properly. I just adjusted it to my topic and resubmitted. The difference was clear immediately.ā€
Favour
Nekede
ā€œMy supervisor almost finished me 😭 He rejected everything and said I didn't understand basics. I downloaded something here, used it to restructure my work, and resubmitted. That was how I escaped serious stress.ā€
Nnamdi
Absu

Can't find what you're looking for?

Search thousands of project topics across every department.

Related Project Materials

See More Mechanical Engineering Final Year Research Project Topics & Materials Ā»

Frequently Asked Questions

Is this project original and plagiarism-free?
Yes. All project materials on iProject are original, well-researched, and crafted to be plagiarism-free. They are intended as academic guides and reference materials.
What format will I receive the material in?
You will receive the complete project in both Microsoft Word (.docx) and PDF formats, making it easy to edit and submit.
How soon will I get it after payment?
Once payment is confirmed, the material is delivered within 24 hours to the email address supplied at checkout.
Can I edit the content to fit my own case study?
Absolutely. The Word format is fully editable, allowing you to modify the content, swap out case studies, and adapt the material to your specific research context.
All My Questions Are Answered — Download the Complete Project
Message us