iProject

DESIGN AND CONSTRUCTION OF RF BASED REMOTE CONTROLLER FOR ELECTRIC LAMP

📄 Project Material📋 65 pages📚 Chapters 1–5💾 MS-Word & PDF

Chapters 1–5  |  ₦5,000

Download Complete Project Now

ABSTRACT

This project work deals on the design and construction of an Rf based remote control for an electronic/electrical device say electric lamp with the aim of switching on/off of the lamp at discretion and from a distance. It also eliminates the inconveniences associated with manual switching of lamps.  This electronic system is designed in two functional units; the transmitter and the receiver using radio frequency (RF) communication wave band.  The transmitter is a hand-held remote control while the receiver consists of a tuned radio frequency receiver, clock generator, delay circuit, flip-flop and a driver circuitry and electromagnetic relay which actuates the load (lamp).  When the remote control button is pressed, the lamp comes ON and remains ON until the remote is pressed again – it goes OFF.  Many advantages are accredited to this design in terms of robust, durability, cost effectiveness and components availability.  The result being the simple design of a system easy to operate and maintain. A miniaturized design of it will be a reliable, robust and rugged consumer electronics that will sell like a German burger.

 

CHAPTER ONE

1.1   INTRODUCTION

Electronic communication has gained a holistic approach in the world technological growth.  Apparently, no modern electronic system is capable of fascinating the society without an aspect of telecommunication. This trend is so progressive that most remote control systems are designed with RF.

 

1.2   GENERAL DESCRIPTION OF THE PROJECT

The above-mentioned development motivated me to embark on a project research work on the design and construction of an Rf based remote control electric lamp.  This electronic system is designed with a handheld remote control realized using frequency generator and modulator coupled into a tuned class-C amplifier.  The amplified signal is radiated into the atmosphere through a tank circuit at a particular frequency. The receiver is realized with a tuned radio frequency (TRF) receiver coupled into a transistor static switch.  These solid state switches are used to clock a D-type flip-flop through a delay circuit. The output of the flip-flop biases a driver circuitry realized using a Darlington pair transistors which drives the relay to switch ON/OFF the lamp connected to its normally open contact, whenever the remote is pressed.

 

1.3   OBJECTIVES OF THE STUDY/PROJECT

One of the objectives of this project is to design and implement an Rf based remote control for electric lamp capable of switching ON/OFF of electric lamp from a maximum distance of 200m at convenience.

It is also aimed at exposing the graduating student to electronic system design using random logic. It is also aimed at familiarizing the young engineers with digital system design involving telecommunication systems.  Another objective of this project is to ground the young engineers in engineering design which is indispensable in engineering professional practice.

 

1.4   SIGNIFICANCE OF THE PROJECT

This project work signifies a lot in telecom, computer and electronic engineering. It is very useful in a number of domestic places like in bedroom and security lamps in the compound. A project of this type if modified can be used as a gate/door opening system, car immobilizer and for industrial process control.  Another vital significance of this system is in the control of Air conditioner and refrigerators and other lamps in modern buildings. This system can be used to start and stop a power generating set from a distance.

 

1.5   SCOPE OF THE PROJECT

This project work covers the following: tuned radio frequency transmitter and receiver, flip-flops, Darlington pair transistors and delay circuits.  It also lays great emphasis on passive and active components used to implement the system. It x-rays the mode of calculation of the basic circuit parameters and other areas of application of the system.

1.6   PROJECT REPORT ORGANIZATION

 

This project is presented in six chapters to appropriately illustrate the steps involved in its implementation. Chapter one introduce the design overview, objective and significance of the project. Chapter two is basically the literature review and some theories relevant to the design. Chapter three x-rays the methodology and analysis. Chapter four is on the system design analysis while chapter five elaborates on the implementation, testing and results. Finally chapter six summarizes the entire thesis and recommendations.

 

This Project is for You If:

Yes, This Is My Situation — Send Me the Complete Material

Here's everything you get with the complete project package:

✔Chapters 1–5 (Word & PDF)
✔Abstract & Table of Contents
✔References, Citation & Bibliography
✔Fully Editable Microsoft Word Format
✔Original, Plagiarism-Free Content
✔Instant Email Delivery
Complete package —₦10,000₦5,000
Price may return to ₦10,000 at any time.

See Our Conversations With Students on WhatsApp

Students sharing their experience after using our service

Urgent delivery confirmed
Urgent delivery confirmed
Payment received and project delivered
Payment received and project delivered
Quality work and a repeat order
Quality work and a repeat order
Returning customer appreciation
Returning customer appreciation
Customer appreciation
Customer appreciation
I’ve Seen Enough — Get Me This Project Material

What Other Students Are Saying

“The process was actually fine and I got my project quickly. The only thing I didn't really like was that I would have preferred they sent it via WhatsApp instead of email, because email took a bit of checking on my side. But once I got it, everything was already complete and I just edited small parts before submitting.”
Zina
Kenpoly
“My supervisor rejected my Chapter 1 and 2 and I was honestly lost. I got a material here and it already had everything arranged properly. I just adjusted it to my topic and resubmitted. The difference was clear immediately.”
Favour
Nekede
“My supervisor almost finished me 😭 He rejected everything and said I didn't understand basics. I downloaded something here, used it to restructure my work, and resubmitted. That was how I escaped serious stress.”
Nnamdi
Absu

Can't find what you're looking for?

Search thousands of project topics across every department.

Related Project Materials

See More Electrical Engineering Final Year Research Project Topics & Materials »

Frequently Asked Questions

Is this project original and plagiarism-free?
Yes. All project materials on iProject are original, well-researched, and crafted to be plagiarism-free. They are intended as academic guides and reference materials.
What format will I receive the material in?
You will receive the complete project in both Microsoft Word (.docx) and PDF formats, making it easy to edit and submit.
How soon will I get it after payment?
Delivery is instant. Once payment is confirmed, the material is sent directly to your email address. You can also download it immediately from the checkout page.
Can I edit the content to fit my own case study?
Absolutely. The Word format is fully editable, allowing you to modify the content, swap out case studies, and adapt the material to your specific research context.
All My Questions Are Answered — Download the Complete Project
Message us