iProject

CONSTRUCTION OF CAR TOUCH INTRUDER ALARM

📄 Project Material📋 65 pages📚 Chapters 1–5💾 MS-Word & PDF

Chapters 1–5  |  ₦5,000

Download Complete Project Now

 

ABSTRACT

The main objective of this project was to ensure a proper security to car being parked in garage against theft or an intruder. The circuit uses three NE555 timers; one of the NE555 was wired as a monostable oscillator and remaining two were wired as tone generator and amplified to obtain a maximum audible sound. However, pin 2 of the first NE555 was used as sensor part .When pin 2 has contact with human body or hand it will activate the IC1 which will also bias transistor and this transistor was wired in a way that once it is powered it will close circuitthereby passing a negative supply voltage to tone generator circuit and outputted out through a loud speaker or buzzer.

This device functions as a major security device against car-theft as stated above. It is an electronic device that is connected to the battery of the car it is being installed in and gets activated when the car engine is switched off and the car stationed at a place. The device is not seen but, it has an indicator light which shows that the alarm has been activated. When the body of the car is touched by human hand, it sends a negative signal to the device which needs a negative pulse to get activated; it sends this negative from the human hand to the tone generator IC which triggers the alarm.   

 

                                         TABLE OF CONTENT

   CHAPTER ONE: Introduction                                                                                  1.1    Background of study

1.2       Aims and objectives

    CHAPTER TWO: Literature Review

    CHAPTER THREE: Specification and operation of system component              3.1       Description of NE55 Timer           

3.2       Description of Resistor

3.3       Description of Capacitor

3.4       Description of Diode

3.5       Description of Transformer

3.6       Description of Loud Speaker and Buzzer

3.7       Description of Transistor

3. 8     Description of L.E.D

    CHAPTER FOUR: Operation of system and its circuit and block diagram

4.1       Operation of  

4.2       The circuit diagram

4.3    The block diagram

    CHAPTER FIVE: Construction, Testing and Packaging

5.1    Values of components

5.2    Assembly

5.3    A schematic diagram of the finished work

    CHAPTER SIX: Conclusion and Recommendation

6.1       Conclusion

6.2       Recommendation

6.3       Observations

6.4       Dificulties

6.5      Reference                        

 

LIST OF SYMBOLS

NAME                                                                     SYMBOLS

                                          

Resistor                                                   

 

 

Transistor

 

Diode                                   

                                        

Zener diode                                   

 

Trimmer capacitor                         

Polarized capacitor                         

Unpolarized capacitor                                    

 

     

Variable capacitor                                                                                      

     

CHAPTER ONE:  INTRODUCTION

1.1.            Background of the Study

        The first car alarm was a primitive contraption that utilized a bell or horn connected to the drive shaft. It was created by an unnamed Nebraska inventor in June 20th, 1920. It utilizes the drive shaft to operate its own bell or horn signal when the car is properly moved. This is just a little talk on a car alarm but not a car touch intruder alarm which is a modern, more advanced, and more reliable type of car alarm.

        This car touch sensitive alarm project consist of three NE555 timer IC, the first NE555 was wired as monostable  multi-vibrator and the remaining two were wired as tone generator. When the sensor is touch or has contact with human hand perhaps body, IC1 is triggered at its pin 2 and output pin 3 goes high for a time period previously set by the values of R4 (10M) and Q1 (transistor) was bias via R3 and this transistor is in such a way that once it was biased it will supply a negative voltage to tone generator thereby making two NE555 timer which was know as (tone generator) to oscillate to make a bell sound through the buzzer. The tone generators are configured as an astable multi-vibrator whose oscillation frequency can be varied with the help of PR1 and PR2. By adjusting the values of PR1 and PR2, modifications on the tone are possible.

The reset button is used to set or open circuit the system back to its initial stage. The system is powered with 12V power supply voltage.

The first chapter of this project is narrating on the introduction, the concept of the system and also the aims and objective. Chapter two is all about literature review. Chapter three talks about specification and operation of system component. Chapter four is operation of system. Chapter five is about construction, testing and packaging. Chapter six is conclusion, observation, recommendation and References.

1.2       AIM AND OBJECTIVE

       The main aim and objective of the design and construction this project is to create a comfort in the minds of vehicle owners or users when their vehicles are parked or stationed anywhere without much fear of car-theft.

This Project is for You If:

Yes, This Is My Situation — Send Me the Complete Material

Here's everything you get with the complete project package:

✔Chapters 1–5 (Word & PDF)
✔Abstract & Table of Contents
✔References, Citation & Bibliography
✔Fully Editable Microsoft Word Format
✔Original, Plagiarism-Free Content
✔Instant Email Delivery
Complete package —₦10,000₦5,000
Price may return to ₦10,000 at any time.

See Our Conversations With Students on WhatsApp

Students sharing their experience after using our service

Urgent delivery confirmed
Urgent delivery confirmed
Payment received and project delivered
Payment received and project delivered
Quality work and a repeat order
Quality work and a repeat order
Returning customer appreciation
Returning customer appreciation
Customer appreciation
Customer appreciation
I’ve Seen Enough — Get Me This Project Material

What Other Students Are Saying

“The process was actually fine and I got my project quickly. The only thing I didn't really like was that I would have preferred they sent it via WhatsApp instead of email, because email took a bit of checking on my side. But once I got it, everything was already complete and I just edited small parts before submitting.”
Zina
Kenpoly
“My supervisor rejected my Chapter 1 and 2 and I was honestly lost. I got a material here and it already had everything arranged properly. I just adjusted it to my topic and resubmitted. The difference was clear immediately.”
Favour
Nekede
“My supervisor almost finished me 😭 He rejected everything and said I didn't understand basics. I downloaded something here, used it to restructure my work, and resubmitted. That was how I escaped serious stress.”
Nnamdi
Absu

Can't find what you're looking for?

Search thousands of project topics across every department.

Related Project Materials

See More Electrical Engineering Final Year Research Project Topics & Materials »

Frequently Asked Questions

Is this project original and plagiarism-free?
Yes. All project materials on iProject are original, well-researched, and crafted to be plagiarism-free. They are intended as academic guides and reference materials.
What format will I receive the material in?
You will receive the complete project in both Microsoft Word (.docx) and PDF formats, making it easy to edit and submit.
How soon will I get it after payment?
Delivery is instant. Once payment is confirmed, the material is sent directly to your email address. You can also download it immediately from the checkout page.
Can I edit the content to fit my own case study?
Absolutely. The Word format is fully editable, allowing you to modify the content, swap out case studies, and adapt the material to your specific research context.
All My Questions Are Answered — Download the Complete Project
Message us