iProject

DESIGN AND CONSTRUCTION OF A REFRIGERATING UNIT

📄 Project Material📋 65 pages📚 Chapters 1–5💾 MS-Word & PDF

Chapters 1–5  |  ₦5,000

Get Complete Project Material Now

 

ABSTRACT

            The design and construction of s refrigerating unit is handled from the knowledge of the working principles of laws of thermodynamics.

            The size of the containing vessel i.e the case as established to be of 45cm by 32 cm in dimension. The Angle iron mild steel to used in the fabrication and welding. The box case of two layers are fabricated. Plastic (cooler) box is then  placed inside the upper part with the other parts of the refrigerator were brought in. they were all fixed onto a wooden base with all the connections (electrical) made.

            The capacity of the refrigerator is based on the workdone by the compressor which is O.I hp in specification. The size of the components used are

i.                    Condenser: The size is 0.1hp and it is a plate type condenser with extended surface.

ii.                  Compressor: The size is 0.1hp (75 watts)

iii.                Copper wire: it is of 0.5cm in diameter and the total copper wire length is about 600cm (1½ roll)

The introduction of cooling fluid and filling of the compressor enabled the compressor to start functioning when connected to electricity using a 13 AMP rated socket

            The interior of the plastic box is lined with dominium box with tubes arranged in convolution around it. This world effectively and cooled the water dropped into it. It compares favorably with the ones in the market.

TABLE OF CONTENT

CHAPTER ONE

1.0              INTRODUCTION

1.1       SCOPE OF THE PROJECT

CHAPTER TWO

HISTORY OF REFRIGERATION

TYPES OF REFRIGERATING DEVICE

USES OF REFRIGERATION

CHAPTER THREE

SEQUENCE OF OPERATIONS

SELECTION OF REFRIGRANTS

CONSTRUCTION PROCEDURE

ECONOMIC ANALYSIS

CHAPTER FOUR

4.1              CONCLUSION

4.2              RECOMMENDATIONS

REFERENCES.

CHAPTER ONE

1.0       INTRODUCTION

            Refrigeration is the process of lowering the temperature of a substance below that of its surrounding.

            Refrigeration is the practical application of the first and second law thermodynamics. Comprehensive understanding of the basic principles of thermodynamics is crucial for full understanding of basic operation of refrigerator. The first law states that the energy can neither be created nor destroyed. If energy of 2.5J appears in one forms it appears in another without a corresponding decrease of energy on the other form. The second law states that no system can receive heat at a given temperature and reject it at a higher temperature without receiving work from the surrounding heat always flow from Warner to cooler body. Through consideration of these laws, the ideal refrigeration cycle are considered. The carnot cycle is reversible and consist of adiabatic compression witherma rejection of heat, adiabatic expansion and wothermal addition of heatl the carnot cycle is unattainable ideal which serves as a standard of comparison and it provides a convenient guide to the temperature that should be maintained to achieved effectiveness. The efficiency or coefficient of performance (C.O.P.) of a carnot cycle depends on the temperature at which heat is added and rejected.

            Therefore,

            C.O.P =           T1

                                    T2 – T1

 Where T1 = Evaporation temperature

            T2 = Conducting temperature

In actual refrigeration there will be issues causing C.O.P to be less than that for ideal cycle. The basic methods of refrigeration like the mechanical refrigeration ejector (steam jet) refrigeration absorption refrigeration uses similar process for obtaining refrigeration effect. That is evaporation in the evaporator, condensation in the condenser, the main difference is in the way used refrigeration being done. The most compression. The cycle efficiency can be ignored in a number of ways.

1.       Multistage system: When evaporation and condensing temperature (pressure) difference is large, it is prudent to separate compression into two stages. The use of multistage system open up the opportunity to use flash gas removal and inter cooling as a measure to improve performance of the system

2.       Cascade system: This appears in situation where the evaporating temperature is very low (below 600c). the refrigerant is used to achieve the cooling. The liquid with low boiling points are used as refrigerants.

1.1       SCOPE OFD THE PROJECT

            The scope of this project is mainly concerned with the design and construction of a refrigerating unit that has a very performance level and with the cost of fabrication lower than that of existing prototype

            A good refrigerator is one that has all the basic components of compressor, condensers, fan motor, copper tubes and other. This project must apply all the principles of refrigeration.

This Project is for You If:

Yes, This Is My Situation — Send Me the Complete Material

Here's everything you get with the complete project package:

✔Chapters 1–5 (Word & PDF)
✔Abstract & Table of Contents
✔References, Citation & Bibliography
✔Fully Editable Microsoft Word Format
✔Original, Plagiarism-Free Content
✔Delivery Within 24 Hours
Complete package —₦10,000₦5,000
Price may return to ₦10,000 at any time.

See Our Conversations With Students on WhatsApp

Students sharing their experience after using our service

Urgent delivery confirmed
Urgent delivery confirmed
Payment received and project delivered
Payment received and project delivered
Quality work and a repeat order
Quality work and a repeat order
Returning customer appreciation
Returning customer appreciation
Customer appreciation
Customer appreciation
I’ve Seen Enough — Get Me This Project Material

What Other Students Are Saying

“The process was actually fine and I got my project quickly. The only thing I didn't really like was that I would have preferred they sent it via WhatsApp instead of email, because email took a bit of checking on my side. But once I got it, everything was already complete and I just edited small parts before submitting.”
Zina
Kenpoly
“My supervisor rejected my Chapter 1 and 2 and I was honestly lost. I got a material here and it already had everything arranged properly. I just adjusted it to my topic and resubmitted. The difference was clear immediately.”
Favour
Nekede
“My supervisor almost finished me 😭 He rejected everything and said I didn't understand basics. I downloaded something here, used it to restructure my work, and resubmitted. That was how I escaped serious stress.”
Nnamdi
Absu

Can't find what you're looking for?

Search thousands of project topics across every department.

Related Project Materials

See More Chemical Engineering Final Year Research Project Topics & Materials »

Frequently Asked Questions

Is this project original and plagiarism-free?
Yes. All project materials on iProject are original, well-researched, and crafted to be plagiarism-free. They are intended as academic guides and reference materials.
What format will I receive the material in?
You will receive the complete project in both Microsoft Word (.docx) and PDF formats, making it easy to edit and submit.
How soon will I get it after payment?
Once payment is confirmed, the material is delivered within 24 hours to the email address supplied at checkout.
Can I edit the content to fit my own case study?
Absolutely. The Word format is fully editable, allowing you to modify the content, swap out case studies, and adapt the material to your specific research context.
All My Questions Are Answered — Download the Complete Project
Message us